What's new at EZE-LAP

Model DMD Knife Sharpening Kit

Sharpen all types of knives with ease.
Holds your edge at the correct angle every time.
Lightweight, convenient and easy to use.
Includes a handy field pouch.

Kit includes:
Knife Clamp
2 x Angle Guides
3 x Guide Rods
3 x 20x 100mm Diamond Sharpening Stones

Price: $124.95

Assembly Attach angle guides to the back of knife clamp using the thumbscrew as shown in Fig 1. Screw guide rod into each stone holder. To attach knife, loosen both thumb screws to fit thickness of knife blade.		Fig 1

Attach clamp to the back of your knife at midpoint as shown in Fig 2. Lightly tighten screw closest to blade. Lock blade by tightening the screw closest to angle guides. Do not over tighten. Do not sharpen if the blade is not secure in the clamp.		Fig 2

Stone and Angle Selection Select desired stone (see stone chart). Place stone holder guide rod through one of the slots in the angle guide as shown in Fig 3. 25 degree angle is recommended for sporting, pocket, work and pocket knives. 20 degree angle for high quality filleting, boning, kitchen and cooks knives.		Fig 3

Sharpening Mode Hold knife clamp as shown in Fig 3. Place stone holder guide rod into desired angle slot. Grasp and place stone holder on knife blade next to handle as shown in Fig 4. Move stone up and down or in a circular motion onto the cutting edge. Use even pressure and overlap strokes as you work down the blade. Do other side of blade, by removing guide rod from slot and turning knife and clamp over. Replace guide rod into the same slot used on first side. Repeat sharpening procedure. For best results, start firm, end light using the same number of strokes on each side. Only light strokes are required to maintain a sharp edge.		Fig 4

Colour			Description
Blue	S Fine	1200g	Final finish, polishing a sharp edge.
Red	Fine	600g	Normal use. Keeps a sharp polished edge on all blades.
Mauve	Medium	400g	Quick metal removal. For dull & damaged blades

Model PB1
EZE-HONE – Plane Blade Sharpener

Sharpen jointer / planner blades in situ

EZE-Hone angled shape locates correct angle
Inbuilt coarse and fine stones
Work on any blade including carbide and high speed steel
Sharpens and hones the blade.

Directions for Use

The shape of the EZE-Hone acts as a guide for correct angle of use.

Place the EZE-Hone against the blade so that the stone makes contact along the cutting edge.

Apply pressure to the EZE-Hone while moving it along the length of the blade.

The amount of pressure will be determined by the condition of the blade (blades that are extremely dull or damaged should be professionally sharpened or replaced).

Start with firm pressure and always finish with light pressure strokes to perform the final honing for a finished edge.

Applying excessive pressure will remove metal very quickly and may cause premature wear on the blades.

Keep blades balanced by using the same number of strokes with the same amount of pressure on each blade.

Use dry, clean with soap and water.

Always turn machinery off prior to sharpening!

Model	Price Incl. GST
PB1	$65.00

Double Sided Diamond Plates

EZE-LAP's double sided plates enable you to sharpen and polish to a razors edge with the convenience of one product. Reshaping can be done with the heavier sided grit, then simply change sides to hone and fine polish using the lighter grit. All double sided plates come with a non-slip mat for ease of use. Available in two sizes and a range of combination grits.

Model	Plates	Description	Price Incl. GST
DD6SF/F	50 x 150mm	Superfine & Fine	$125.00
DD6SF/M	50 x 150mm	Superfine & Medium	$125.00
DD6F/C	50 x 150mm	Fine & Coarse	$125.00
DD8SF/F	75 x 200mm	Superfine & Fine	$198.00
DD8SF/M	75 x 200mm	Superfine & Medium	$198.00
DD8F/C	75 x 200mm	Fine & Coarse	$198.00

Chisel Care Kit

EZE-LAP bring you everything you need for a sharp chisel or planer blade in one kit.

Our diamond plate provides the perfect sharpening surface while the sharpening guide takes the guess work out of sharpening at the right angle.

The revolutionary Sentry Solutions
TUF-CLOTH™ multi-purpose dry protectant, cleans, protects and lubricates your chisel without oils or silicones to prevent friction and wear.

Model	Each Kit contains	Plate	Price Incl. GST
CCKF Chisel Care Kit	50 x 150 x 6mm Diamond	Fine (600 Grit) Chisel Guide TUF-CLOTH™	$98.00

What's new at EZE-LAP

Model DMD Knife Sharpening Kit

Double Sided Diamond Plates

Chisel Care Kit

[Top]

© Copyright 1999 A.M. Dungey Pty. Ltd. All rights reserved

Website design by MICROVISION microvision@internode.on.net